The main function of a shower faucet with valve is to divert water from the tub spout to the showerhead. You can install this type of valve on either the hot or cold side of your tub.
TS valves prevent scalding
Shower faucets with TS valves prevent scalded water and have two separate control mechanisms. One controls pressure and the other controls temperature. Thermostatic valves allow you to set the water temperature independently of the water volume, and maintain it within a few degrees. This feature allows you to set the desired temperature while showering and does not change even after the water is shut off. Thermostatic valves are more expensive than pressure-balance valves, but they provide the most protection from scalding water.
TS valves help reduce scalding water, which is a significant health risk for children. These valves are designed to prevent the water from exceeding the maximum temperature set by the consumer. These valves are typically fitted with override buttons that allow you to change the thermostat settings from the "typical" to the "unsafe" setting. Despite their name, they still present a risk for scalding if not installed properly.
Diverter valves divert water from a tub spout to a showerhead
A diverter valve is a valve that diverts water from a tub spout into a showerhead. This type of valve is also known as a 2 way diverter. The diverter is used in traditional bathtubs and showers, but does not have anti-scald features. These systems are becoming mandatory in many states in the USA. A diverter valve consists of two parts: the rough diverter valve body and the diverter trim. The rough diverter valve body is fixed to the outside of the wall and has a lever handle to control the flow of water. A diverter valve is typically used in a bathtub or shower with a spout and a showerhead installed above it.
A diverter valve can come in two different designs. One type has two handles, one for hot water and one for cold water. A diverter with two handles has two separate openings, while a 3-valve unit has only one handle to control both water flows. Diverters come in a variety of sizes and styles. To find the best fit for your tub, you should first measure the distance between the two faucets.
Service stops on a shower valve are optional
Before you buy a new shower valve, you should confirm the number of ports you need. Depending on your home or apartment, you may only need three ports. In these cases, you can choose a valve with service stops. However, if you need four, you will not be able to get a four-port valve. This is especially useful in apartments. You should always make sure to check the number of ports that you need before you buy the valve.
To remove a service stop, you should remove the trim kit attached to the shower valve. The stop is typically made of screw-driver slots. If the shower valve has no service stops, you may need to call the manufacturer to have a replacement part sent to your home. Otherwise, you can do it yourself by using a screw-driver. It is also possible to change the stops on the valve at other points in the hot and cold lines. If you can't access them easily, you should contact a plumber or a professional.
Common problems with shower valves
Many of the common problems with shower valves are easily fixed. The first step is to shut off the water supply. Next, you should protect the drain to avoid water damage. Ideal shower plumbing will come with a valve for the local water supply. However, in most cases, this valve is not present. In such a case, it will be necessary to replace the entire shower valve. However, this is not an expensive process and can be done without affecting your daily routine.
Another common problem with shower valves is that they leak. This happens because the O-rings have worn out. Replacing the O-rings is an easy task that does not require much expertise. If you can fix the problem yourself, you'll save a lot of money. You can purchase a handle puller for $9-15 from your local hardware store. You may also use Teflon tape to cover the screw.
Repairing a leaky shower faucet
A leaky shower faucet with valve can be a frustrating problem. Not only does it waste water, but it can also cause a large water bill. Not to mention that it can lead to the growth of mold and wood rot. However, there are several simple ways to repair a leaky faucet with valve. These methods are simple and can be performed by the average homeowner. Once you have completed this repair, you will have a properly functioning shower faucet once again.
First, turn off the water supply. If the leak is caused by the faucet itself, you may need to shut off the water supply before attempting to repair it. If the leak is coming from the valve, you may need to call a plumber. Otherwise, you can try the DIY method below. If you choose to do this repair yourself, you will be able to avoid the inconvenience of going without water for a long period of time.
